Universal Remote Control ONE FOR ALL PVR 6 Guide de l'utilisateur télécharger pdf (Page 10)

8

One For All 6-Device PVR Universal Remote Control

For example, to nd out which code is

operating your TV:

1. On the remote control, press TV once.

2. Press and hold SETVOUJMUIF-&%SFE

light) blinks twice, then release SET.

 &OUFS9 9 0ćF-&%XJMMCMJOLUXJDF

4. To view the code for the rst digit,

press 1 once. Wait 3 seconds, count

UIF-&%CMJOLTFHUISFFCMJOLT

3) and write down the number in the

lemost box in the TV code boxes on

page 6.

NOTE: If a code digit is 0, the LED will not

CMJOL

5. Repeat step 4 three more times for

remaining digits. Use 2 for the second

digit, 3 for the third digit, and 4 for

the fourth digit. Write down the code

digits in the remaining TV code

boxes on page 6.

6. To check for codes of other devices,

repeat steps 1 through 5, but

substitute the appropriate device key

for each device you are checking.

Write down the device’s code digits in

the appropriate code boxes on page 6.

PROGRAMMING MASTER POWER

In its default state, the POWER key

on the URC-6131 remote control

will individually power your home

entertainment devices on or o.

However, you can also program a Master

Power function onto the POWER key that

will sequentially turn on or o all the

devices with a single key press.

PROGRAMMING THE POWER KEY FOR

MASTER POWER

1. Press and hold SETVOUJMUIF-&%SFE

light) blinks twice, then release SET.

 &OUFS9 9 5ćF-&%XJMMCMJOLUXJDF

en press POWER once.

3. For the rst device you want in the

power on sequence, press its device

key (e.g., CBL/SAT) once.

4. Repeat step 3 up to ve more times to

add desired devices to the power-on

sequence.

5. To save the settings and exit the

program, press and hold SET until the

-&%CMJOLTUXJDFUIFOSFMFBTFSET.

OPERATING MASTER POWER

1. Aer programming, point the

remote control at the devices and

press POWER for at least 2 seconds

to sequentially turn on or o your

devices.

NOTE: When you press POWER for less than

2 seconds, the remote will only send a

QPXFSDPNNBOEUPUIFDVSSFOUMZTFMFDUFE

device. is allows you to still individually

power devices on or o.

 :PVXJMMTFFUIFEFWJDFTUVSOPOPS

o according to your programmed

sequence.

NOTE:ćFDVSSFOUMZTFMFDUFEEFWJDFXJMM

always turn on rst, followed by the

remaining programmed sequence. Aer

the master power sequence is complete, the

SFNPUFXJMMDPOUSPMUIFĕSTUQPXFSFEPO

device.

NOTE: If one or more devices does not have

B108&3LFZUIFQPXFSPČPOTFRVFODF

may be slightly delayed when the remote

control signals the device(s). is action is

normal.

CLEARING MASTER POWER

1. Press and hold SETVOUJMUIF-&%SFE

light) blinks twice, then release SET.

 &OUFS9 9 5ćF-&%XJMMCMJOLUXJDF

en press POWER once.

3. Press and hold SETVOUJMUIF-&%

blinks twice, then release SET.BTUFS

Power is now cleared.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 37 38

Commentaires sur ces manuels

Pas de commentaire