Universal Remote Control MX-880Z - SPECS SHEET Informations techniques Page 172

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 180
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 171
© 2000–2014 Schneider Electric
All Rights Reserved
Masterpact™ NT and NW Universal Power Circuit Breakers
Trip Curves
172
05/2014
Figure 168: Micrologic 5.0/6.0 A/P/H Trip Units: Short-Time Pickup and I
2
t ON Delay
1.5
1
1
CURRENT IN MULTIPLES OF Ir (Ir = LONG-TIME SETTING x In)
CURRENT IN MULTIPLES OF Ir
(Ir = LONG-TIME SETTING x In)
.5
.6
.7
.8
.9
1.5
2
3
4
5
6
7
8
9
10
15
20
30
40
50
60
70
80
90
100
.5
.6
.7
.8
.9
2
3
4
5
6
7
8
9
10
15
20
30
40
50
60
70
80
90
100
200
300
400
500
600
700
800
900
1000
1500
2000
3000
4000
6000
7000
8000
9000
5000
10000
.005
.006
.007
.008
.009
.01
.015
.02
.03
.04
.05
.06
.07
.08
.09
.1
.005
.006
.007
.008
.009
.01
.015
.02
.03
.04
.05
.06
.07
.08
.09
.1
.15
.2
.3
.4
.5
.6
.7
.8
.9
1
.15
.2
.3
.4
.5
.6
.7
.8
.9
1
1.5
2
3
4
5
6
7
8
9
10
1.5
2
3
4
5
6
7
8
9
10
15
20
30
40
50
60
70
80
90
100
15
20
30
40
50
60
70
80
90
100
150
200
300
400
500
600
700
800
900
1000
1500
2000
3000
4000
5000
6000
7000
8000
9000
10000
TIME IN SECONDS
CYCLE
2
1
1 CYCLE
150
2.52
345
68101. 5
0.4 ON
0.4 ON
0.2 ON
0.3 ON
0.1 ON
0.3 ON
0.2 ON
0.1 ON
SHORT-TIME
DELAY I
2
t ON
SECONDS AT 10 x Ir
SHORT-TIME
PICKUP
x Ir
MAXIMUM
UNRESTRAINED
SHORT-TIME
DELAY
Curve No. 0613TC0005
Drawing No. B48095-613-05
Micrologic 5.0/6.0 A/P/H Trip Units
Characteristic Trip Curve No. 613-5
Short-Time Pickup and I
2
t ON Delay
The time-current curve information is to be used for
application and coordination purposes only.
Curves apply from -30°C to +60°C (-22°F to +140°F)
ambient temperature.
NOTE:
1. There is a thermal-imaging effect that can act to
shorten the long-time delay. The thermal-imaging
effect comes into play if a current above the long-time
delay pickup value exists for a time and then is cleared
by the tripping of a downstream device or the circuit
breaker itself. A subsequent overload will cause the
circuit breaker to trip in a shorter time than normal. The
amount of time delay reduction is inverse to the
amount of time that has elapsed since the previous
overload. Approximately twenty minutes is required
between overloads to completely reset thermal-
imaging.
2. The end of the curve is determined by the interrupting
rating of the circuit breaker.
3. With zone-selective interlocking ON, short-time delay
utilized, and no restraining signal, the maximum
unrestrained short-time delay time band applies
regardless of the setting.
4. Total clearing times shown include the response times
of the trip unit, the circuit breaker opening, and the
extinction of current.
5. For withstand circuit breaker, instantaneous can be
turned OFF. See trip curve 613-7 for instantaneous trip
curve. See trip curve 613-10 for instantaneous
override values.
6. See trip curve 613-4 for long-time pickup and delay trip
curve.
Vue de la page 171

Commentaires sur ces manuels

Pas de commentaire